A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.

A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 and 2x4 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x4 is 35 lbs and the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.

A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 and 2x4 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x4 is 35 lbs and the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.

A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 and 2x4 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x4 is 35 lbs and the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.

A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 and 2x4 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x4 is 35 lbs and the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.

A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 and 2x4 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x4 is 35 lbs and the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.

A high performance LED flat panel designed for installation in drop ceilings; typically used to replace standard 2x2 and 2x4 fluorescent fixtures. The profile is slim, only 3 inches deep including the junction box, so the fixture is ideal for low depth ceiling cavities. The housing and the back panel are aluminum to provide maximum heat sink and thermo control capabilities. The trim also acts as a heat sink, and in keeping with the high quality of the rest of the materials the lens is a translucent white polycarbonate. Because of the quality and solidity of the materials, the fixtures have weight; the 2x4 is 35 lbs and the 2x2 is 14 lbs. (Earth quake safety tabs included).

Both panels are fully dimmable with a smooth 12 level remote dimmer, and both are wired for smart controls.

MASTER/SLAVE: Each panel (both 2x2 and 2x4) has a Master/Slave switch on the back. During mounting, one fixture in the room should be switched to Master, and the others in the room should be switched to Slave. With supplied regular RJ25 cord (telephone cords with telephone jacks) each fixture is joined to the next (see diagram left)

ROOM CONTROL: When all the units are joined, one remote control aimed at the Master Unit will control all the other units in the room, up to a maximum of 10 units. With one click, all the units can be turned on, dimmed and turned off. The Master Unit controls the whole room, up to 10 fixtures.

BUILDING CONTROL: Multiple panels can also be controlled from a single source. The panels can be linked to a DMX512 controller.